[NTLUG:Discuss] Fedora on Dell PowerEdge 700 does not find NIC
MadHat
madhat at unspecific.com
Fri Apr 9 22:42:45 CDT 2004
On Apr 9, 2004, at 3:35 PM, Neil Aggarwal wrote:
> Hello:
>
> This is strange. The attachment is not on the copy I get
> from the list.
>
> Are attachments removed by the listserver?
>
Not all. You have to make it a .txt or something the software can
detect and know it is not an issue. Better to post to a website and
send a link anyway.
> Thanks,
> Neil
>
>
> --
> Neil Aggarwal, JAMM Consulting, (972)612-6056, www.JAMMConsulting.com
> FREE! Valuable info on how your business can reduce operating costs by
> 17% or more in 6 months or less! =>
> http://newsletter.JAMMConsulting.com
>
>> -----Original Message-----
>> From: discuss-bounces at ntlug.org
>> [mailto:discuss-bounces at ntlug.org] On Behalf Of Neil Aggarwal
>> Sent: Friday, April 09, 2004 3:22 PM
>> To: 'NTLUG Discussion List'
>> Subject: RE: [NTLUG:Discuss] Fedora on Dell PowerEdge 700
>> does not find NIC
>>
>>
>> Justin:
>>
>> Here it is again.
>>
>> Here is the output of lspci -vv again:
>>
>> 00:00.0 Host bridge: Intel Corp. 82875P Memory Controller Hub (rev 02)
>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR+ FastB2B-
>> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort+ >SERR- <PERR-
>> Latency: 0
>> Region 0: Memory at fe800000 (32-bit, prefetchable) [size=4M]
>> Capabilities: [e4] #09 [3106]
>>
>> 00:03.0 PCI bridge: Intel Corp. 82875P Processor to PCI to CSA Bridge
>> (rev 02) (prog-if 00 [Normal decode])
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR+ FastB2B-
>> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 64
>> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>> I/O behind bridge: 0000e000-0000efff
>> Memory behind bridge: fe100000-fe2fffff
>> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>>
>> 00:1c.0 PCI bridge: Intel Corp.: Unknown device 25ae (rev 02) (prog-if
>> 00 [Normal decode])
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR+ FastB2B-
>> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 64, cache line size 10
>> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
>> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>> Capabilities: [50] PCI-X non-bridge device.
>> Command: DPERE+ ERO- RBC=0 OST=4
>> Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
>> DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
>> 00:1d.0 USB Controller: Intel Corp.: Unknown device 25a9 (rev 02)
>> (prog-if 00 [UHCI])
>> Subsystem: Dell Computer Corporation: Unknown device 0167
>> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>> DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin A routed to IRQ 16
>> Region 4: I/O ports at cce0 [size=32]
>>
>> 00:1d.4 System peripheral: Intel Corp.: Unknown device 25ab (rev 02)
>> Subsystem: Dell Computer Corporation: Unknown device 0167
>> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>> DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Region 0: Memory at fe300400 (32-bit, non-prefetchable)
>> [size=16]
>>
>> 00:1d.5 PIC: Intel Corp.: Unknown device 25ac (rev 02) (prog-if 20
>> [IO(X)-APIC])
>> Subsystem: Dell Computer Corporation: Unknown device 0167
>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR+ FastB2B-
>> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Capabilities: [50] PCI-X non-bridge device.
>> Command: DPERE- ERO- RBC=0 OST=0
>> Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
>> DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
>> 00:1d.7 USB Controller: Intel Corp.: Unknown device 25ad (rev 02)
>> (prog-if 20 [EHCI])
>> Subsystem: Dell Computer Corporation: Unknown device 0167
>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR+ FastB2B-
>> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
>> DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin D routed to IRQ 23
>> Region 0: Memory at fe300000 (32-bit, non-prefetchable)
>> [size=1K]
>> Capabilities: [50] Power Management version 2
>> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
>> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>> Capabilities: [58] #0a [2080]
>>
>> 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 0a)
>> (prog-if 00 [Normal decode])
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR+ FastB2B-
>> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
>> I/O behind bridge: 0000d000-0000dfff
>> Memory behind bridge: fc000000-fdffffff
>> BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
>>
>> 00:1f.0 ISA bridge: Intel Corp.: Unknown device 25a1 (rev 02)
>> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
>> ParErr+ Stepping- SERR+ FastB2B-
>> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>> DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>>
>> 00:1f.2 IDE interface: Intel Corp.: Unknown device 25a3 (rev 02)
>> (prog-if 8a [Master SecP PriP])
>> Subsystem: Dell Computer Corporation: Unknown device 0167
>> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr-
>> DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0
>> Interrupt: pin A routed to IRQ 17
>> Region 0: I/O ports at <unassigned>
>> Region 1: I/O ports at <unassigned>
>> Region 2: I/O ports at <unassigned>
>> Region 3: I/O ports at <unassigned>
>> Region 4: I/O ports at fea0 [size=16]
>>
>> 00:1f.3 SMBus: Intel Corp.: Unknown device 25a4 (rev 02)
>> Subsystem: Dell Computer Corporation: Unknown device 0167
>> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>> DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Interrupt: pin B routed to IRQ 17
>> Region 4: I/O ports at 08c0 [size=32]
>>
>> 01:01.0 Ethernet controller: Intel Corp.: Unknown device 1075
>> Subsystem: Dell Computer Corporation: Unknown device 0167
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B-
>> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr-
>> DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 0 (63750ns min), cache line size 10
>> Interrupt: pin A routed to IRQ 18
>> Region 0: Memory at fe1e0000 (32-bit, non-prefetchable)
>> [size=128K]
>> Region 2: I/O ports at ece0 [size=32]
>> Capabilities: [dc] Power Management version 2
>> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
>> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
>>
>> 03:0e.0 VGA compatible controller: ATI Technologies Inc Rage
>> XL (rev 27)
>> (prog-if 00 [VGA])
>> Subsystem: Dell Computer Corporation: Unknown device 0167
>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+
>> ParErr- Stepping+ SERR- FastB2B-
>> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
>> DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR-
>> Latency: 32 (2000ns min), cache line size 10
>> Region 0: Memory at fc000000 (32-bit, non-prefetchable)
>> [size=16M]
>> Region 1: I/O ports at dc00 [size=256]
>> Region 2: Memory at fdeff000 (32-bit, non-prefetchable)
>> [size=4K]
>> Expansion ROM at <unassigned> [disabled] [size=128K]
>> Capabilities: [5c] Power Management version 2
>> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
>> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>>
>> Thanks,
>> Neil
>>
>>
>> --
>> Neil Aggarwal, JAMM Consulting, (972)612-6056, www.JAMMConsulting.com
>> FREE! Valuable info on how your business can reduce operating
>> costs by
>> 17% or more in 6 months or less! =>
>> http://newsletter.JAMMConsulting.com
>>
>>> -----Original
>> Message-----
>>> From: discuss-bounces at ntlug.org
>>> [mailto:discuss-bounces at ntlug.org] On Behalf Of Justin M. Forbes
>>> Sent: Friday, April 09, 2004 10:09 AM
>>> To: NTLUG Discussion List
>>> Subject: Re: [NTLUG:Discuss] Fedora on Dell PowerEdge 700
>>> does not find NIC
>>>
>>>
>>> Can you please send me the output of 'lspci -vv' and attach a
>>> copy of your
>>> /etc/mudules.conf? This should not be happening, so I will
>>> see what the
>>> deal is, it is possible that Dell used a new revision of the
>>> onboard or
>>> something which identifies differently, if so, I will send
>>> you an updated
>>> hwdata which should fix autodetection for other servers.
>>>
>>> Thanks,
>>> Justin M. Forbes
>>>
>>> _______________________________________________
>>> https://ntlug.org/mailman/listinfo/discuss
>>>
>>
>
>
> _______________________________________________
> https://ntlug.org/mailman/listinfo/discuss
>
More information about the Discuss
mailing list