[NTLUG:Discuss] Fedora on Dell PowerEdge 700 does not find NIC
Neil Aggarwal
neil at JAMMConsulting.com
Fri Apr 9 15:35:26 CDT 2004
Hello:
This is strange. The attachment is not on the copy I get
from the list.
Are attachments removed by the listserver?
Thanks,
Neil
--
Neil Aggarwal, JAMM Consulting, (972)612-6056, www.JAMMConsulting.com
FREE! Valuable info on how your business can reduce operating costs by
17% or more in 6 months or less! => http://newsletter.JAMMConsulting.com
> -----Original Message-----
> From: discuss-bounces at ntlug.org
> [mailto:discuss-bounces at ntlug.org] On Behalf Of Neil Aggarwal
> Sent: Friday, April 09, 2004 3:22 PM
> To: 'NTLUG Discussion List'
> Subject: RE: [NTLUG:Discuss] Fedora on Dell PowerEdge 700
> does not find NIC
>
>
> Justin:
>
> Here it is again.
>
> Here is the output of lspci -vv again:
>
> 00:00.0 Host bridge: Intel Corp. 82875P Memory Controller Hub (rev 02)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at fe800000 (32-bit, prefetchable) [size=4M]
> Capabilities: [e4] #09 [3106]
>
> 00:03.0 PCI bridge: Intel Corp. 82875P Processor to PCI to CSA Bridge
> (rev 02) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000e000-0000efff
> Memory behind bridge: fe100000-fe2fffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>
> 00:1c.0 PCI bridge: Intel Corp.: Unknown device 25ae (rev 02) (prog-if
> 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, cache line size 10
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [50] PCI-X non-bridge device.
> Command: DPERE+ ERO- RBC=0 OST=4
> Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
> DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
> 00:1d.0 USB Controller: Intel Corp.: Unknown device 25a9 (rev 02)
> (prog-if 00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0167
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 4: I/O ports at cce0 [size=32]
>
> 00:1d.4 System peripheral: Intel Corp.: Unknown device 25ab (rev 02)
> Subsystem: Dell Computer Corporation: Unknown device 0167
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Region 0: Memory at fe300400 (32-bit, non-prefetchable)
> [size=16]
>
> 00:1d.5 PIC: Intel Corp.: Unknown device 25ac (rev 02) (prog-if 20
> [IO(X)-APIC])
> Subsystem: Dell Computer Corporation: Unknown device 0167
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Capabilities: [50] PCI-X non-bridge device.
> Command: DPERE- ERO- RBC=0 OST=0
> Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
> DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
> 00:1d.7 USB Controller: Intel Corp.: Unknown device 25ad (rev 02)
> (prog-if 20 [EHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0167
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 23
> Region 0: Memory at fe300000 (32-bit, non-prefetchable)
> [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] #0a [2080]
>
> 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 0a)
> (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: fc000000-fdffffff
> BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
>
> 00:1f.0 ISA bridge: Intel Corp.: Unknown device 25a1 (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:1f.2 IDE interface: Intel Corp.: Unknown device 25a3 (rev 02)
> (prog-if 8a [Master SecP PriP])
> Subsystem: Dell Computer Corporation: Unknown device 0167
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 17
> Region 0: I/O ports at <unassigned>
> Region 1: I/O ports at <unassigned>
> Region 2: I/O ports at <unassigned>
> Region 3: I/O ports at <unassigned>
> Region 4: I/O ports at fea0 [size=16]
>
> 00:1f.3 SMBus: Intel Corp.: Unknown device 25a4 (rev 02)
> Subsystem: Dell Computer Corporation: Unknown device 0167
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 17
> Region 4: I/O ports at 08c0 [size=32]
>
> 01:01.0 Ethernet controller: Intel Corp.: Unknown device 1075
> Subsystem: Dell Computer Corporation: Unknown device 0167
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr-
> DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (63750ns min), cache line size 10
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at fe1e0000 (32-bit, non-prefetchable)
> [size=128K]
> Region 2: I/O ports at ece0 [size=32]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
>
> 03:0e.0 VGA compatible controller: ATI Technologies Inc Rage
> XL (rev 27)
> (prog-if 00 [VGA])
> Subsystem: Dell Computer Corporation: Unknown device 0167
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+
> ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
> DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2000ns min), cache line size 10
> Region 0: Memory at fc000000 (32-bit, non-prefetchable)
> [size=16M]
> Region 1: I/O ports at dc00 [size=256]
> Region 2: Memory at fdeff000 (32-bit, non-prefetchable)
> [size=4K]
> Expansion ROM at <unassigned> [disabled] [size=128K]
> Capabilities: [5c] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> Thanks,
> Neil
>
>
> --
> Neil Aggarwal, JAMM Consulting, (972)612-6056, www.JAMMConsulting.com
> FREE! Valuable info on how your business can reduce operating
> costs by
> 17% or more in 6 months or less! =>
> http://newsletter.JAMMConsulting.com
>
> > -----Original
> Message-----
> > From: discuss-bounces at ntlug.org
> > [mailto:discuss-bounces at ntlug.org] On Behalf Of Justin M. Forbes
> > Sent: Friday, April 09, 2004 10:09 AM
> > To: NTLUG Discussion List
> > Subject: Re: [NTLUG:Discuss] Fedora on Dell PowerEdge 700
> > does not find NIC
> >
> >
> > Can you please send me the output of 'lspci -vv' and attach a
> > copy of your
> > /etc/mudules.conf? This should not be happening, so I will
> > see what the
> > deal is, it is possible that Dell used a new revision of the
> > onboard or
> > something which identifies differently, if so, I will send
> > you an updated
> > hwdata which should fix autodetection for other servers.
> >
> > Thanks,
> > Justin M. Forbes
> >
> > _______________________________________________
> > https://ntlug.org/mailman/listinfo/discuss
> >
>
More information about the Discuss
mailing list